WOT - is this the ONLY way to remove carbon buildup?
Cadillac
 

Cadillac Forums | Help Us Help You | Advertise | Cadillac Parts | Cadillac News | Cadillac Classifieds / (Old System)

Cadillac Technical Archive | Cadillac Dealers | Cadillac Reviews | Cadillac Dealer Reviews | Cadillac Vendors

CadillacForums.com is the premier Cadillac Forum on the internet. Registered Users do not see the above ads.
+ Reply to Thread
Page 1 of 2 1 2 LastLast
Results 1 to 15 of 28
Like Tree7Likes
Northstar Engines and System Technical Discussion Discussion, WOT - is this the ONLY way to remove carbon buildup? in Cadillac Engine Technical Discussion; Hey there fellas, I was wondering... Is WOT the ONLY way to remove the carbon buildup in a Northstar. I ...
  1. #1
    detroit99sts is offline Cadillac Owners Fanatic
    Join Date
    May 2005
    Posts
    242

    WOT - is this the ONLY way to remove carbon buildup?

    Hey there fellas,
    I was wondering... Is WOT the ONLY way to remove the carbon buildup in a Northstar. I have a 99 STS, if that makes any difference. Is there another way?..ie chemicals, cleaners,etc...

    thanks

    -Mike

  2. Remove Advertisements
    CadillacForums.com
    Advertisements
     

  3. #2
    CadillacSTS42005's Avatar
    CadillacSTS42005 is offline Banned
    Automobile(s): 2005 STS4 1SG: GM Acc Lights, Corsa, Platnium Grille, Volant
    Join Date
    Oct 2005
    Posts
    15,992

    Re: WOT - is this the ONLY way to remove carbon buildup?

    fuel system treament would help it a lil Lucas is the best

  4. #3
    Kev's Avatar
    Kev
    Kev is offline Cadillac Owners 10000+ Posts
    Automobile(s): 1989 Sedan DeVille is now just a fond memory ....
    Join Date
    Aug 2004
    Location
    Left Coast (Central)
    Age
    54
    Posts
    10,414

    Re: WOT - is this the ONLY way to remove carbon buildup?

    Quote Originally Posted by detroit99sts
    Hey there fellas,
    I was wondering... Is WOT the ONLY way to remove the carbon buildup in a Northstar. I have a 99 STS, if that makes any difference. Is there another way?..ie chemicals, cleaners,etc...

    thanks

    -Mike
    Are you adverse to the WOT process? It's probably the most economical way to do it and it is good for the engine now and then. A good hard acceleration once in a while is good for most any engine.

  5. #4
    detroit99sts is offline Cadillac Owners Fanatic
    Join Date
    May 2005
    Posts
    242
    Thread Starter

    Re: WOT - is this the ONLY way to remove carbon buildup?

    Quote Originally Posted by Kev
    Are you adverse to the WOT process? It's probably the most economical way to do it and it is good for the engine now and then. A good hard acceleration once in a while is good for most any engine.
    Im not really adverse to it. I just am scared that so much pressure and the engine revving high may lead to something else going wrong. I stil do WOT's, but I am scared to do it ALL THE TIME. Maybe I am scared because I have had to replace an engine already. Thank God I had a warranty or else it would have cost me $7800. I am just trying to avoid any engine damage, if possible. Anything else available in addition to Lucas?

    -Mike

  6. #5
    mcowden is offline Cadillac Owners Connoisseur
    Join Date
    Jun 2003
    Posts
    1,164

    Re: WOT - is this the ONLY way to remove carbon buildup?

    Quote Originally Posted by detroit99sts
    Im not really adverse to it. I just am scared that so much pressure and the engine revving high may lead to something else going wrong. I stil do WOT's, but I am scared to do it ALL THE TIME. Maybe I am scared because I have had to replace an engine already. Thank God I had a warranty or else it would have cost me $7800. I am just trying to avoid any engine damage, if possible. Anything else available in addition to Lucas?

    -Mike
    I would use Top Engine Cleaner (GM TEC) before anything from Lucas. Chevron Techron is also supposed to work well, at least for deposits, but you have to mix it 50/50 with gas before using it. I don't know how well Techron works for carbon, but TEC was made for carbon I believe. There is a procedure you can follow that involves putting the TEC in cylinders, leaving it a while, then vacuuming it out. Maybe someone can chime in here with the details of that. It's intended to free sticky and/or carboned rings. Or you could just remove the heads and clean everything up with a toothbrush. :-)
    Mike

  7. #6
    Katshot's Avatar
    Katshot is offline Cadillac Owners Master
    Join Date
    Jan 2003
    Location
    Newtown, PA
    Age
    55
    Posts
    6,472

    Re: WOT - is this the ONLY way to remove carbon buildup?

    Top Engine Cleaner IS the best way. It's certainly not as fun as the WOT procedure but it is safer for the engine and does a much more thorough job.
    As I recall, there's directions on the can but I used to use it as follows:
    1. Warm engine
    2. with engine at idle, induce the Top Engine Cleaner into the intake tract. This is easy with a carburetor, but still do-able with EFI. You just need to be a little more "creative". Basically, the theory is to get the solvent into the combustions chamber area and quickly stall the engine so you don't simply burn-off the solvent. You want it to remain in there to soak into the carbon. I leave it that way for about 10-15min and then come back and start the engine. I let it run for a minute or so, revving it slightly until the smoke clears fairly well. Then I take it out on the road and open her up for a couple WOT runs.
    Things to watch out for:
    1. DO NOT pour solvent into the engine after the engine stalls
    2. Understand that when the engine is started, it will smoke BIG TIME, so make sure to park the car where tons of smoke won't cause a problem.
    3. If you simply run the solvent through the engine and don't stall it and allow solvent to soak into the carbon, you aren't accomplishing much.

  8. #7
    Ranger's Avatar
    Ranger is online now Cadillac Owners Member
    Automobile(s): White Diamond '03 DHS (with DTS floor shift)
    Join Date
    Jun 2004
    Location
    Woodstock Ill.
    Age
    66
    Posts
    74,483

    Re: WOT - is this the ONLY way to remove carbon buildup?

    As mentioned, GM top engine cleaner is the alternative method. More expense, more work and less fun. The Northstar was designed to be run long and hard. I forget the number but during testing they were run for hundreds of hours on end at WOT on a dyno at the factory. You won't hurt it. Take her out and whoop her! Here is a quote from our old friend and guru.

    "There are many advantages to occasional full throttle accelerations with a Northstar and any engine.

    It keeps the carbon cleaned out of the combustion chamber. This is maybe a little more important with the Northstar than some other engines due to the tight squish volumes between the piston and the cylinder head. It's designed this way to promote good in-cylinder mixture motion (good combustion) but it has the down side of providing a ready place for carbon build-up to touch the piston - causing noise. Ever heard of the Northstar "cold carbon rap" problem?? Simply put you'll hear a rythmic, piston slap-like noise when the engine is cold. Very prominent and very annoying. Cause: excessive carbon build up causing the the piston to contact the carbon on the head - causing it to rock in the bore and "slap" Much more evident when the engine is cold and the pistons haven't expanded to full diameter yet. Simplest and easiest "fix" for this: A few good WOT (wide open throttle) accelerations to clear the carbon out. That is all it takes to eliminate the problem and prevent it from re-occurring.

    Occasional WOT accelerations also help seat the rings to the ring lands and exercise the rings and keep them mobile and from becoming stuck in carbon in the ring lands. At high RPM and WOT the rings move around on the piston - they actually rotate on the piston and will polish away any carbon and seat themselves to the sides of the ring grooves. This is especially important on the 2000 and later Northstars which had hard anodized top ring lands on the pistons. Very hard and wear resistant - also harder to break-in and seat the rings to the sides of the ring-lands to promote the best possible seal. Many oil consumption complaints on the 2000 and later engines are related, to some extent, with the rings never seating to the sides of the ring-grooves due to lack of load as the engine was babied around forever. Even engines with rings stuck in the ring-grooves due to carbon build up can eventually be freed up with enough high RPM operation.

    WOTs warm up the engine thoroughly and clean out the exhaust due to temperature in the exhaust and high flow rates blasting particles, rust and such out of the system.

    Frequent WOT operation will not hurt the engine or the transmission. They're designed for that. The healthiest engines that I have seen at high miles are always the ones that are run the hardest. Rings are free on the pistons and sealing; no carbon buildup.

    The exercise that I think works best for many things is to select manual 2nd gear on an isolated stretch of expressway. This takes the transmission shifting out of the question if you are worried about hurting it. Start at 55 MPH or so and go to WOT in 2nd gear and hold it until the RPM reaches near the normal shift point - i.e. 6500 for an L37 and 6000 for an LD8. Hold the throttle wide open until the engine reaches, say, 6200 for an STS and then just let completely off the throttle. Leave the transmission in 2nd so that the engine brakes the car and creates some pretty heavy over-run conditions at high vacuum levels. Let it slow until it is about 55 or so and then go to WOT again and repeat. This exercise really loads the rings, allows variable RPM operation at WOT for several seconds continuously, creates heavy over-run which tends to unload the rings and make them move and thus exercise them in the ring grooves and it will blow-out carbon and the exhaust - all without creating a spectical of yourself and attracting the attention of cops. You can do it on most any freeway and stay within the 70-75 MPH range allowable. Once a week like this will keep the engine cleaned out and healthy and is DEFINITELY recommended for the Northstar in particular.

    The Northstar engine was designed/developed/validated to be run hard. It was expected that people would use the performance of the engine - which few people seem to do. The biggest single problem that many issues stem from is lack of use at full throttle by the owners. It just doesn't like to be babied around. The rings are low-tension by design for good high RPM operating characteristics and low friction/good power. They work best if "used" and kept free.

    In every conversation with owners I have had, once the owner started doing the WOTs and using the power of the engine they report no more carbon rap, better oil economy, no "smoke" when they do light it up (keep the exhaust cleaned out. If you notice a "cloud" at WOT then you are not doing enough WOTs...) etc... A bit of judicious use of the other end of the throttle travel is a GOOD thing."

  9. #8
    detroit99sts is offline Cadillac Owners Fanatic
    Join Date
    May 2005
    Posts
    242
    Thread Starter

    Re: WOT - is this the ONLY way to remove carbon buildup?

    So Ranger,
    do you think the Top Engine Cleaner will provide approximately the same results as your 2nd gear WOT method? Which method will produce better results? Thanks,

    -Mike

  10. #9
    iametarq's Avatar
    iametarq is offline Cadillac Owners Connoisseur
    Automobile(s): None
    Join Date
    Dec 2004
    Location
    Petoskey, MI
    Age
    33
    Posts
    3,289

    Re: WOT - is this the ONLY way to remove carbon buildup?

    Ranger, THANK YOU for finally clarifing the WOT technique with the quote from your friend.

    Quote Originally Posted by Rangers Friend
    The exercise that I think works best for many things is to select manual 2nd gear on an isolated stretch of expressway. This takes the transmission shifting out of the question if you are worried about hurting it. Start at 55 MPH or so and go to WOT in 2nd gear and hold it until the RPM reaches near the normal shift point - i.e. 6500 for an L37 and 6000 for an LD8. Hold the throttle wide open until the engine reaches, say, 6200 for an STS and then just let completely off the throttle. Leave the transmission in 2nd so that the engine brakes the car and creates some pretty heavy over-run conditions at high vacuum levels. Let it slow until it is about 55 or so and then go to WOT again and repeat. This exercise really loads the rings, allows variable RPM operation at WOT for several seconds continuously, creates heavy over-run which tends to unload the rings and make them move and thus exercise them in the ring grooves and it will blow-out carbon and the exhaust - all without creating a spectical of yourself and attracting the attention of cops. You can do it on most any freeway and stay within the 70-75 MPH range allowable. Once a week like this will keep the engine cleaned out and healthy and is DEFINITELY recommended for the Northstar in particular.
    THAT paragraph explains exactly what should be done, and how to do it. I think that is the section that should be high lighted in the Tech Documents on this site. Now my only problem is the nearest expressway to me, I-75 is an hour away.

  11. #10
    Katshot's Avatar
    Katshot is offline Cadillac Owners Master
    Join Date
    Jan 2003
    Location
    Newtown, PA
    Age
    55
    Posts
    6,472

    Re: WOT - is this the ONLY way to remove carbon buildup?

    While I agree that some accassional WOT runs aren't a bad thing, there needs to be some common sense applied to that paragraph though. I doubt anyone at Cadillac would stand by a statement that suggests "frequent" WOT runs are not in anyway bad for the drivetrain, or that the harder it's driven the better. Most, if not ALL OEMs have a rather dim view of customers thrashing their cars regularly. Somehow I have a sneaking suspicion that if you took your STS to the dealer with a drivetrain failuer and told them it happened at the track while racing, they'd probably think twice about covering the damage under warranty. I don't have an owner's manual but I assume there's something in it about racing the cars or abusive driving habits being cause for denial of warranty coverage.

  12. #11
    mtflight's Avatar
    mtflight is offline Cadillac Owners Connoisseur
    Automobile(s): 1999 White Diamond ETC
    Join Date
    Jan 2005
    Location
    Dallas, TX
    Posts
    2,531

    Re: WOT - is this the ONLY way to remove carbon buildup?

    What about Top Engine Cleaner and other strong solvents vs. headgaskets, seals, insulators, etc inside the engine?

    Especially with the "leave overnight part" that is sometimes recommended.

  13. #12
    Ranger's Avatar
    Ranger is online now Cadillac Owners Member
    Automobile(s): White Diamond '03 DHS (with DTS floor shift)
    Join Date
    Jun 2004
    Location
    Woodstock Ill.
    Age
    66
    Posts
    74,483

    Re: WOT - is this the ONLY way to remove carbon buildup?

    Quote Originally Posted by detroit99sts
    So Ranger,
    do you think the Top Engine Cleaner will provide approximately the same results as your 2nd gear WOT method? Which method will produce better results? Thanks,

    -Mike
    I really don't know for sure but the WOT treatment is certainly easier, cheaper and more fun. Try a few applications. If it doesn't work, then you can always have the top engine treatment done.

  14. #13
    thu's Avatar
    thu
    thu is offline Cadillac Owners Connoisseur
    Automobile(s): 2003 STS w/BoseNav, 1993 Deville, 1985 Deville
    Join Date
    Jul 2003
    Location
    Wyoming
    Posts
    1,089

    Re: WOT - is this the ONLY way to remove carbon buildup?

    The Top End Cleaner method sounds too much like work. WOT is quick, easy, and harmless. In addition it costs waaaaay less and takes waaaaay less time than TEC.

  15. #14
    ELDORACER's Avatar
    ELDORACER is offline Cadillac Owners Member
    Join Date
    Oct 2005
    Location
    Cleveland
    Age
    27
    Posts
    38

    Re: WOT - is this the ONLY way to remove carbon buildup?

    i did both very happy with results TEC and regular WOTs

  16. #15
    lry99eldo is offline Cadillac Owners Fanatic
    Join Date
    Apr 2005
    Posts
    157

    Re: WOT - is this the ONLY way to remove carbon buildup?

    I've found over all the years I've driven and the many engines that I have built that the best carbon build up prevention is to take the long route to a familiar place and cruise it for 5 miles or more at highway speed in the one lower gear. This increases the RPMs slightly, doesn't overstress any of the drivetrain, increases the amount of fuel and temperature within the combustion chamber and helps to clear and or keep clear the carbon build up.
    I've never had a problem, even with engines 11:1 or more that I've built. Of course, these engines were built to be rev'ed high, yet I would do the above procedure anyway just to be sure.
    lry99eldo

Quick Reply Quick Reply

Register Now

Please enter the name by which you would like to log-in and be known on this site.
If you do not want to register, fill this field only and the name will be used as user name for your post.

Please enter a password for your user account. Note that passwords are case-sensitive.

Please enter a valid email address for yourself.

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Bookmarks

Cadillac Posting Rules

  • You may post new threads
  • You may post replies
  • You may not post attachments
  • You may not edit your posts
Read about Lincoln | Buick | Kia Forte Forum
Need products for your Cadillac? Check out your options at the links below:

custom floor mats | Cadillac Chrome and Black Chrome Wheels | window tinting