: Performance Mods For 3.6 LY7??

07-03-06, 01:11 AM
Hi, I'm from Australia and I run a 3.6 LY7 in my race car. It currently is stock apart from a set of performance exhaust pipes and K and N air filter. Does anyone know of any mods to cams etc. There isn't much in the the way of after market bits in OZ yet. Any help or info would be great.

Jim Gunther
07-05-06, 09:16 AM
Looks like this hasn't caught on YET.
On paper, it looks like the engine of the future (6 Cyl anyway).
I posted a call for exterior measurements recently (see a couple posts below). Short of going to a boneyard and measuring the mounts, oil pan etc, I don't know if I'll be able to use it in my Stalker. , I haven't seen anything but a couple photos of the motor with all the Caddilac plastic hiding the cam covers.
I's like to see how you've used YOUR motor (i.e. is your application a 7-esque or a full bodied car or ??)

01-16-07, 08:19 PM
Hi I have attached some photos of the car for you to see. Still have not been able to find any parts.

Jim Gunther
01-30-07, 08:48 AM
Just saw your photos 1/30/07. Very nice. I like the headers.
Car used for circle track racing?
Is that a standard throttle body (or whatever they call it).

Are there "generic" modifications that are commonly done? i.e. bigger injectors, throttle bodies, altering cams or ?power curves?
TIA and good luck. Keep us posted.

02-01-07, 07:48 PM
Yes the car is a speedway car ( dirt circle track). I have the only one that I know of in this class of racing. So I am the one who has to do the home work on how to make more power. As it still runs the factory ECM it makes it hard to change anything at the moment until I find a aftermarket ECM to run the VVT and Electric Throttle (class rule require this). The headers are a off the shelf set made for road cars. If you have any leads or info it would be great.

Jim Gunther
02-16-07, 04:44 PM
>>If you have any leads or info it would be great
Sorry, I'm in the same boat. I'm going to try one (or two) more people at GM. SOMEBOY's got to have trries SOMETHING with this motor!

(PS: I was travelling and just saw your 2/1/posting)

08-17-07, 05:25 PM
any more parts out yet - and where can i get them online?

08-22-07, 11:03 PM
umm.... a tune?

08-27-07, 10:41 PM
i have done everything that is available in australia,
cai, k&n filter, extractors, high flow cats, performance exhaust, and a custom tune.

currenlty 236.3rwhp


any one making cams yet?

08-29-07, 11:55 PM
make a custom SC.



09-01-07, 12:53 PM
what about possibly milling the head a little ... im no engineer, hell im not even a mechanic but if my math is right shaving off about .027 should get your compression ratio up to 11.0, u might even wanna take off maybe another 0.001, raise it up to 11.2 ... if the tl's 3.2 can handle it i'm sure the 3.6 can w/o risk of detonation or messing with the internals ...

08-30-08, 06:37 AM
well i have a supercharger now.....8psi

in my car check out the dyno sheet for before and after results.
hptuners was the software used but is still limited performance wise

09-03-08, 01:58 PM
Where did you get the Supercharger from? and how much did it cost? Is it available for the US

03-15-14, 07:15 PM
nice!!!! where can I fine one of those:yup:

Ve sv6
03-26-14, 08:59 AM
nice!!!! where can I fine one of those:yup:

C.A.P.A, an online automotive shop over here in Australia but I'm sure they would post.